E3D Hot End Parts

Items 21 to 27 of 27 total

per page
Page:
  1. 1
  2. 2
  3. 3

Grid  List 

Set Descending Direction
  1. Embedded Bowden Couplings - For Metal (3mm Filament)

    Embedded Bowden Couplings - For Metal (3mm Filament)

    $3.50

    These pneumatic fittings have a brass metal body which is designed to provide a simple and cost effective way of inserting bowden tubing directly into your aluminium components. The couplings are designed to take 1/4 Inch OD tubing and the brass inserts push into an 0.528 Inch hole 0.181 Inches deep. E3D apologises for the use of imperial units. These fittings are aimed at use within the 3mm Bowden v6 product, however there are plenty of other applications ready to be discovered. Learn More
  2. E3D-V6 .4mm nozzle for 3mm Filament

    E3D-V6 .4mm nozzle for 3mm Filament

    $12.00

    Out of stock

    1 x E3D-V6 .4mm nozzle for 3mm Filament Learn More
  3. E3D-V6 .4mm nozzle for 1.75mm Filament

    E3D-V6 .4mm nozzle for 1.75mm Filament

    $12.00

    1 x E3D-V6 .4mm nozzle for 1.75mm Filament Learn More
  4. E3d-Lite6 100k Thermistor Kit

    E3d-Lite6 100k Thermistor Kit

    $6.00

    E3d-Lite6 Thermistor

     

    Options:

    Fully Assembled Thermistor (ATC Semitec 104GT-2)

    • Fully Assembled ATC Semitec 104GT-2 Thermistor with 1M long wires for E3d-Lite6 hot end, a quick disconnect 100mm From the thermistor, uses High Temp Sleeving to insulate the wires and a connector labeled with THERM to connect to your electronics.

    Thermistor Install Kit (ATC Semitec 104GT-2)

    • ATC Semitec 104GT-2 Thermistor with High Temp PTFE Sleeving Installed
    • Pre-wired 2 Pin connector with wire (Good for Printrboard & RAMPS)
    • Heat Shrink Tubing
    Learn More
  5. E3d-v6 100k Thermistor Kit

    E3d-v6 100k Thermistor Kit

    $8.00

    E3d-v6 100k thermistor

    Thermistor Install Kit Includes the following:

    • ATC Semitec 104GT-2 Thermistor with High Temp PTFE Sleeving Installed
    • Pre-wired 2 Pin connector with wire (Good for Printrboard & RAMPS)
    • Heat Shrink Tubing
    • crimping ferrules
    • fiberglass sleeve
    Learn More
  6. 24v 30W Ceramic Heater Cartridge for Hot Ends

    24v 30W Ceramic Heater Cartridge for Hot Ends

    $4.50

    Specs: Current: 24v Power output: 30W Core: Ceramic Diameter: 6mm Length: 23mm Wire Length: 100cm Learn More
  7. Silicone Pro Socks for v6 - Pack of 3

    Silicone Pro Socks for v6 - Pack of 3

    $4.75

    A pack of 3x high temperature non-stick silicone socks for E3D-v6 and other hotends also using the E3D-v6 style heater block with thermistor cartridges. They will not properly fit the screw-washed clamped thermistor style E3D-v6 Block. These socks fit the new cartridge style thermistor blocks. To upgrade to the new block and thermistor, with 3x socks purchase the Block and Sock Kit 

    Read all about them in the Blog Post!

    • These socks will keep your nozzle clean and free of burnt on blackened plastic. They don’t just keep the nozzle clean, but also keep heat inside the hotend, and off the print.
    • Made of a heat-resistant, non-stick silicone material our will repel build-up of molten plastic. This really helps with sticky materials like Co-Polyesters and filled materials that like to build up on nozzles.
    • These also offer a huge boost in temperature stability, particularly if you use high airflow cooling around the nozzle to cool the print. The additional cooling combined with reduced radiation of heat from the block and nozzle to the print really boost the ability to print great overhangs and bridges, all while keeping the hotend temperature extremely stable.
    • The covers simply push onto the front of the hotend with no disassembly - they will be a tight fit when first pushed on cold. When hot the silicone will expand to the correct size to fit the hotend snugly. The elastic material will fit all nozzle sizes in the range from 0.25mm to 0.80mm

    These v6 socks come in a pack of 3 because they don’t last forever. Depending on what materials you print and how much abuse they get they eventually wear away at the nozzle tip. Even with sticky abrasive materials and a bit of abuse they should easily last 100+ print hours. With less sticky materials like ABS and gentler use you can get almost infinite life. Your mileage may vary.

    Learn More

Items 21 to 27 of 27 total

per page
Page:
  1. 1
  2. 2
  3. 3

Grid  List 

Set Descending Direction