JHead Hot End Parts

Items 1 to 10 of 13 total

per page
Page:
  1. 1
  2. 2

Grid  List 

Set Descending Direction
  1. 6mm Kapton Tape 33 Meters long

    6mm Kapton Tape 33 Meters long

    This tape is 6mm wide, and the roll tape is 0.5cm thickness. Kapton Tape is used to assemble a hot end or secure a thermistor to your heat bed. Great for heated applications, and insulating electrical joints and heating elements. It has tons of uses and is easy to clean up when you remove it. Learn More
  2. Resistor & Thermistor Set

    Resistor & Thermistor Set

    $4.00

    This is the Resistor & thermistor set for the J-Head Style hot-end for 1.75mm Filament this will not work with any other hot end and it will not work with the J-Head MK IVB,

    3 Watt 6.8 Ohm Resistor G550 Thermistor

    Learn More
  3. PTFE Liner for J-Head Style Hot End 1.75mm

    PTFE Liner for J-Head Style Hot End 1.75mm

    $3.75

    This is the PTFE filament liner for this hot end: J-Head Style hot-end for 1.75mm Filament this will NOT work with any other hot end and it will NOT work with the J-Head MK IVB, If your hot end currenlty uses 3mm Filament this will NOT work for your hot end.

    Learn More
  4. 24v 30W Ceramic Heater Cartridge for Hot Ends

    24v 30W Ceramic Heater Cartridge for Hot Ends

    $4.50

    Specs: Current: 24v Power output: 30W Core: Ceramic Diameter: 6mm Length: 23mm Wire Length: 100cm Learn More
  5. 12v 30W Ceramic Heater Cartridge for Hot Ends

    12v 30W Ceramic Heater Cartridge for Hot Ends

    $4.25

    Specs: Current: 12v Power output: 30W Core: Ceramic Diameter: 6mm Length: 23mm Wire Length: 100cm Learn More
  6. Thermistor and Resistor High Temp Sleeve

    Thermistor and Resistor High Temp Sleeve

    $1.95

    High Temperature Sleeving for the Thermistor and Resistor. Includes enough sleeving for 1 Thermistor and 1 Resistor. Learn More
  7. Hot End Mounting Plate

    Hot End Mounting Plate

    $2.00

    This Hot End Mounting Plate will mount your Hot End under your Extruder Learn More
  8. Brass Nozzle (Mk I to Mk IV)

    Brass Nozzle (Mk I to Mk IV)

    $27.50

    This brass nozzle is machined from a solid piece of brass bar stock. In order to simplify the assembly, improve the heat transmission, and reduce the size of the unit, the heater block and thermistor mounting hole are integrated with the nozzle. This nozzle is compatible with hot-ends Mk I through MK IV for 3mm filament Learn More
  9. Hollow Set Screw

    Hollow Set Screw

    $1.50

    hollow-lock socket set screw. This set screw is compatible with nozzle holder versions 2, 3, and 4. It is used to retain the PTFE liner. Learn More
  10. PTFE Liner (Mk IV)

    PTFE Liner (Mk IV)

    $4.25

    This is the PTFE filament liner for a Mk IV J-Head hot-end. The ID is 0.128" and the OD is 0.250". One end has a taper for properly seating in the nozzle. This ptfe liner is for 3mm filament. Learn More

Items 1 to 10 of 13 total

per page
Page:
  1. 1
  2. 2

Grid  List 

Set Descending Direction