Electronics / Motors / LCD's

Electronics for 3D Printers like the RepRap

Items 11 to 19 of 19 total

per page
Page:
  1. 1
  2. 2

Grid  List 

Set Descending Direction
  1. Arduino Mega Clone 2560

    Arduino Mega Clone 2560

    $20.00

    Used in the ramps 1.4 electronics. Learn More
  2. Rumba Board

    Rumba Board

    $84.00

    Completely assembled RUMBA kit

    • 1 x RUMBA Board

     

    The board will have jumpers installed for 1/16th steps if you pick a4988 or 1/32nd steps if you pick DRV8825 drivers

    Picture shown with Rumba and 4 x a4988 Stepper Drivers and Heat Sinks Option Blue screw driver pictured is no longer included Learn More
  3. 8gb ADATA MicroSDHC Card with adapter

    8gb ADATA MicroSDHC Card with adapter

    $6.50

    Compatible with our LCD control panels. Learn More
  4. Heat Bed Relay

    Heat Bed Relay

    $16.50

    This Heat Bed Relay will allow you to run larger heat beds that require more power then your electronics can supply.  This is perfect for the 8.4" x 12.6" Heat Bed, 10" x 10" Heat Bed, 12" x 12" heat bed and even help to heat up your 8" x 8" MK1 or MK2 quicker.

     

    Connect J2 to one heat bed wire and GND from your power supply.  Connect J1 In to 12v+ from your power supply and connect the other heat bed wire to J1 out, then connect the two small Pre-Soldered wires to your Heat Bed out put of your electronics (D8 for RAMPS)

    Learn More
  5. Full Graphic LCD Controller with Smart Adapter

    Full Graphic LCD Controller with Smart Adapter

    Regular Price: $69.00

    Special Price $60.00

    The Smart LCD Controller lets you print without a PC.

    Kit Includes 1 Smart Adapter (Fully Assembled)

    1 A graphical smart controller with a 128x64 Dots LCD and a SD Card reader

    30-35cm long flat cables, with the smart adaptor.

    1 set of Headers to connect to your RAMPS 1.4 Board (May require Soldering)

    Firmware, hardware and settings required: Firmware: You need Marlin firmware v3 or newer. If you are using older firmware, you must re-flash your board. The latest Marlin firmware is available here: github.com/ErikZalm/Marlin Hardware required: - Ramps 1.4 - Mega2560 board - SD Card Configuration: After re-flash you must edit the config.h according to my post in reprap wiki. reprap.org/wiki/RepRapDiscount_Smart_Controller

    Or you can download the preconfigured firmware here: RAMPS Graphical LCD Firmware

    Learn More
  6. Nema 17 Stepper Motor - 76oz-in D Shaft Motors

    Nema 17 Stepper Motor - 76oz-in D Shaft Motors

    Nema 17 Stepper Motor - Pre-Wired 

    Stepper motor : SINGLE (NEMA17) - Including connector for RAMPS Electronics

    Specification:

    5mm Shaft
    Holding Torque : 76 oz-in
    Assembled with a 4 way Molex connector and 890mm (35") cables
    20mm long D Shaft style so your Gears won't slip
    1.8 Steps
    48mm Long

    Learn More
  7. A4988 Stepper Driver

    A4988 Stepper Driver

    $9.00

    Those are 100% compatible drivers with Pololu schematic diagram and genuine A4988 IC on it, those are not inferior A4984 drivers !!! The A4988 is a complete microstepping motor driver with built-in translator for easy operation. It is designed to operate bipolar stepper motors in full-, half-, quarter-, eighth-, and sixteenth-step modes, with an output drive capacity of up to 35 V and ±2 A. The A4988 includes a fixed off-time current regulator which has the ability to operate in slow or mixed decay modes. The translator is the key to the easy implementation of the A4988. Simply inputting one pulse on the STEP input drives the motor one microstep. There are no phase sequence tables, high frequency control lines, or complex interfaces to program. The A4988 interface is an ideal fit for applications where a complex microprocessor is unavailable or is overburdened. During stepping operation, the chopping control in the A4988 automatically selects the current decay mode, Slow or Mixed. In Mixed decay mode, the device is set initially to a fast decay for a proportion of the fixed off-time, then to a slow decay for the remainder of the off-time. Mixed decay current control results in reduced audible motor noise, increased step accuracy, and reduced power dissipation. Internal synchronous rectification control circuitry is provided to improve power dissipation during PWM operation. Internal circuit protection includes: thermal shutdown with hysteresis, undervoltage lockout (UVLO), and crossover-current protection. Special power-on sequencing is not required. Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic supply Thermal shutdown circuitry Short-to-ground protection Shorted load protection Five selectable step modes: full, 1/2, 1/4, 1/8, and 1/16 Learn More
  8. SD Ramps - Clearance

    SD Ramps - Clearance

    Regular Price: $0.99

    Special Price $0.25

    Ever wanted to run your RepRap from SD card? Here is your chance! This RAMPS add-on enables you to print from MicroSD. With RAMPS 1.3 and higher it's easily connected to the RAMPS board. For more information, check this page: reprap.org/wiki/Sdramps NOTE: Kingston brand SD cards do not work as they do not support SPI. Learn More
  9. 12v/29A Meanwell Power Supply

    12v/29A Meanwell Power Supply

    $48.00

    This ultra low profile Power Supply delivers 12 Volts with 29 Amps. This is the ideal Power Supply for most electronic setups. "This Power Supply is a solid 12V power source for your projects!" Product Details Qty. 1 12V/29A 215mm(~8.50") x 115mm(~4.5") x 30mm(~1.25") Voltage select switch 110V - 220V 2 DC Outputs Built-in Cooling Fan 85% Efficiency UL 60950-1 Approved Pro-tip: You can easily mount this unit using Single L Brackets and M4 Socket Head Cap Screws. The fan is temperature controlled. It only turns on when the PSU internals heat up above 50degC and then turns back off once the internals fall below 40degC again. Warning - Be sure to disconnect power before attempting to to switch voltage. Power Supply should always be unplugged while you make the connections and also make sure the shield is in place before plugging the cord into an outlet. Warning - high voltage! Always have a qualified electrician connect this unit. Use at your own risk! Learn More

Items 11 to 19 of 19 total

per page
Page:
  1. 1
  2. 2

Grid  List 

Set Descending Direction